User Profile

Nelia Bryant

Bio Statement

Continue to cut lengths alternately from one roll and the other, keeping the 2 separated. The very first, third, 5th, and so on, lengths will have one leading, while the 2nd, 4th, sixth, and so on, will be various.

"Wallpaper patterns may be divided into two principal classes, the ""one-top"" or straight pattern papers, and the ""two-top"" or drop patterns. It is required to cut these documents so that the design matches when hung. For this reason consideration of the design is essential before cutting such papers. The top of a flower or figure must not be cut in half. The paper should be so positioned that a whole flower or figure should be left about a 1/2 inch listed below the picture molding. A ""one-top"" or straight-patterned paper is one in which the style matches on opposite sides of the paper. They are easy and great for tasks in a kid's bathroom, with patterns that match the bathroom components or bath tub. Before cutting the paper, the needed length is to be determined. When this has been done, the paper is unrolled face up. Let us assume that the wall to be covered is 8' high. Allowance must be produced cutting and cutting at the top and bottom. This need to be at least 6"". It may be necessary to cut more depending upon the pattern. For example, a paper may have a pattern which is 12"" high. If there is no room at the top for cutting, the entire pattern should be cut off because, as has actually been stated, the top must constantly have a whole pattern resting about 1/2"" listed below the photo molding or ceiling line. Permitting 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right-hand man, pull out 11/2"" from the roll. Let this hang over completion of the table, and then unroll 7', which will cover the length of the table. Take a look at the style to figure out the finest place to cut, bearing in mind that the top of the pattern will be about 1/2"" below the image molding. This first piece may be a bit longer in order to get the top right. The remainder of the paper is cut into equal lengths of 8' 6"". Do not do this in the restroom. No bathtub is a good work table, even if it is a walk-in tub. A ""two-top"" or drop pattern is one in which the style does not fall directly opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for example, the adjacent pattern will be 10"" listed below this. It can be seen, then, that a drop pattern paper can not be cut the like a straight-pattern paper. If all lengths were cut the exact same, every other length would not match at the top This is especially obvious in little places like restrooms, where the wallpaper is among the only things to take a look at while awaiting the sauna or sitting in the tub. The wallpaper is noticeable from the shower too. The simplest method to cut these documents is to take lengths from separate rolls. Cut the very first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top. Continue to cut lengths at the same time from one roll and the other, keeping the 2 separated. The very first, third, 5th, and so on, lengths will have one top, while the second, fourth, sixth, etc., will be various. Prior to hanging the very first width, the location at which to begin should be figured out. This is found by deciding which the most prominent walls are. They are normally those in between windows and over the mantel. Then identify the least noticeable place in the space and plan the work to end up there, so if an inequality takes place, it will be least noticeable. If there is no mantel in the space, the very first width should be hung between the windows. Then follow around to the right, covering one side of the room. Return to the window end and paper the opposite. By this plan of procedure, you will always have great light. If you are working in a bathroom with no windows, attempt affixing a bright lamp onto the shower tray or the shower doors (this might be hard with frameless shower doors) to remove most shady corners. If there is a mantel in the space, the first pieces are positioned there, because it is the most conspicuous point. The wall over the mantel is marked so that the paper will be centered. This treatment is as follows: Measure the width of wall over the mantel to find the center. Draw the line through this center. If the area requires 4 widths, place the very first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These 3 widths are short lengths. The remaining part will be covered with two partial widths of full length. Cut these 1/2"" broader than needed, so regarding have the edges turn the corner."